Skip to content
Carbide snow plow blades, inserts and wear parts — engineered in Rayong, Thailand
Request a Quote

Cobalt policy: reading them for edge budgets

Cobalt policy in a cutting edge specification is a purchasing control, not a metallurgical preference: it sets how much cobalt-bearing alloy you accept, who verifies it, and at…

Cobalt policy in a cutting edge specification is a purchasing control, not a metallurgical preference: it sets how much cobalt-bearing alloy you accept, who verifies it, and at what price and lead time. For a distributor or fleet buyer, the practical answer is to fix a cobalt range and a verification method in the purchase order, then let the edge geometry and wear part do the rest.

This article is written for buyers who sign off on cutting edge specifications and then have to defend the cost per lane-kilometre or per operating hour. It does not recommend a cobalt content. It explains how to read a supplier’s cobalt policy so that the number on the quotation matches the number in the steel.

What a cobalt policy actually covers

Cobalt in a cutting edge is usually present because the base steel is a tool steel or a through-hardened alloy where cobalt contributes to hot hardness and wear resistance. A supplier’s cobalt policy should therefore state three things: the grade family, the accepted cobalt range, and the test method used to confirm it. If any of those three is missing, the policy is a marketing statement rather than a specification.

Ask for the policy as a document with a revision number. A verbal “we use the same steel as before” is not a policy, because “before” is not a controlled reference.

Reading the grade family before the cobalt number

Cobalt content is meaningless outside its grade family. A 6% cobalt figure in one tool steel and a 6% figure in another are not interchangeable, because carbon, chromium, vanadium and molybdenum levels shift the hardness and toughness balance. Read the grade designation first, then the cobalt range, then the hardness window.

  1. Identify the grade designation and the standard it is quoted against.
  2. Record the cobalt range as a minimum and maximum, not a nominal figure.
  3. Record the hardness window and the test location on the edge.
  4. Confirm whether the cobalt figure refers to the melt analysis or a finished-part check.
  5. Confirm who holds the mill certificate and for how long.
  6. Confirm what happens if a delivered lot falls outside the stated range.

Steps 4 to 6 are where most specification risk sits. A melt analysis describes the heat; a finished-part check describes what you actually received. Both are legitimate, but they answer different questions.

Cobalt content, wear life and the ranges that matter

Higher cobalt in the relevant grades tends to correlate with better retained hardness at elevated temperature, which matters on abrasive, high-speed service. It does not follow that more cobalt always means longer life. Toughness, edge geometry, bolt torque and the operator’s down-pressure setting can each move field life by more than a small change in cobalt content.

For budgeting, treat life as a range and state the assumption behind it. On mixed abrasive service, a well-specified cobalt-bearing edge might run somewhere in the region of one and a half to three times the life of a standard carbon-steel edge, depending on the grade, the surface, and the blade angle. That is a planning range, not a guarantee, and it should be replaced with your own fleet data as soon as you have two or three seasons of it.

Cost behaves the same way. The price premium for a cobalt-bearing grade over a standard edge varies with mill surcharges, order quantity and geometry, and it is rarely a fixed percentage. Ask for the premium as a separate line on the quotation so it can be reviewed independently of the base edge price.

Verification: certificates, sampling and dispute handling

Verification is the part of a cobalt policy that protects the buyer, and it should be agreed before the first shipment rather than after the first complaint. The table below sets out the common verification options and what each one is good for.

Method What it confirms Practical note
Mill certificate (EN 10204 3.1) Heat analysis of the steel supplied to the edge maker Strongest documentary evidence; ties the heat to the lot if lot traceability is maintained
Supplier declaration of conformity That the supplier believes the part meets the stated grade Weaker than a mill certificate; acceptable for low-risk, repeat orders
In-house spectrometer check Chemistry of the finished part Destructive or semi-destructive; agree sampling frequency and who pays
Third-party assay Independent chemistry confirmation Reserve for disputes or new suppliers; slow and costly per sample

Whichever method you choose, write the acceptance range and the remedy into the purchase order. A policy without a remedy clause is advice, not a control. Confirm exact parameters on the product page before you commit the range to a tender document.

What the cobalt policy means commercially

Commercially, a cobalt policy is a supply-chain decision. Tighter cobalt ranges and stronger verification narrow the pool of mills and edge makers who can quote, which usually lengthens lead time and raises the minimum order quantity needed to justify a dedicated heat. Looser ranges widen the pool and shorten lead time, at the cost of more variation between lots.

Total cost of ownership should be built from three lines: edge price, change-out labour and downtime, and the risk cost of a lot that fails verification. For a fleet, the middle line often dominates. For a distributor, the third line matters more, because a rejected lot sits in your warehouse and in your customer’s memory. There is no single correct setting; there is only the setting you can defend with your own change-out records.

Specification risk also has a contract dimension. If your tender documents quote a cobalt range, bidders will price to that range. Reading public bid tabulations for cutting edges is a useful discipline here, because it shows how competitors describe grade and verification in writing, and where the wording is loose enough to create later argument.

Writing the cobalt clause into a purchase order

A workable clause is short and testable. It names the grade, gives the cobalt range as min and max, states the verification method and sampling frequency, and names the remedy for a failed lot. It also states the revision of the supplier’s policy it relies on, so that a later policy change cannot be applied retroactively to an open order.

Keep the clause stable across seasons unless you have data justifying a change. Buyers who revise cobalt requirements every order tend to lose both price stability and the supplier’s willingness to hold stock. If you need a second reference point for how edge specifications are written and compared, the guidance on reading public bid tabulations for cutting edges covers the comparison side in more detail.

Finally, record the assumption set behind your budget: grade, cobalt range, verification method, expected life range and change-out cost. When actual life lands outside the range, the assumption set tells you whether the problem was the specification, the supply, or the operating condition.

Quick summary

A cobalt policy is a purchasing control that fixes the grade family, the cobalt range and the verification method, and it should be written into the purchase order with a remedy clause. Read it for supply, lead time and specification risk rather than as a wear guarantee, and replace generic life ranges with your own fleet data as soon as it exists.

Sources checked on 2026-11-16: supplier policy documents and mill certificate conventions as described by the manufacturer; general tool-steel grade nomenclature; the linked SENTHAI product and technical pages; the linked guidance on reading public bid tabulations for cutting edges.

Three more perspectives

Workshop: The fitter cares whether the edge bolts up flat and stays flat. A tight cobalt range is irrelevant if the bolt holes are out of position or the edge is not straight, so pair the chemistry clause with a dimensional check on receipt.
Purchasing: The buyer cares whether the premium is visible and reviewable. Ask for the cobalt premium as a separate quotation line and hold the policy revision number on file against each order.
Field: The operator cares whether the edge wears evenly. Uneven wear usually points to blade angle, down-pressure or surface mix before it points to cobalt content, so collect change-out records by machine and by site.

Limits

This page is not a grade recommendation, not a hardness specification and not a substitute for the mill certificate or the manufacturer’s product data. It does not quantify wear life for any specific surface, machine or operating weight, and it does not address welding, hardfacing or refurbishment of worn edges. Figures described as ranges are planning assumptions only and should be replaced with measured fleet data. Confirm exact parameters on the product page before quoting any cobalt range in a tender or purchase order.

Products discussed in this thread

Send us a blade drawing and get a quote back

Tell us the machine, the material you are clearing and the wear life you need. Our engineers reply with the edge profile, carbide grade and packing that fit the job — usually within one working day.