Skip to content
Carbide snow plow blades, inserts and wear parts — engineered in Rayong, Thailand
Request a Quote

Season close-out for fleet managers

Season close-out for fleet managers means one thing: deciding which cutting edges to re-order now, which to hold, and which to retire before the next snow season starts.…

Season close-out for fleet managers means one thing: deciding which cutting edges to re-order now, which to hold, and which to retire before the next snow season starts. The decision should be based on measured wear, not on how the edge looks in the yard. This page sets out a practical close-out sequence for procurement and maintenance teams, with the specification and commercial points that usually get missed.

What “close-out” actually covers

Close-out is the period between the last deployment and the next pre-season fit. It is the only window in the year when you can inspect edges off the plow, compare wear against the previous set, and change the specification without a truck sitting idle. Treat it as an inspection and planning task, not a purchasing task that happens to fall in spring.

The output of close-out is a short document per plow: what came off, what it measured, what goes back on, and what gets bought. If your team cannot produce that document, the re-order will default to last year’s part number, which is how fleets end up carrying a specification they no longer need.

Inspection sequence before anything is scrapped

Pull the edges, clean them, and record them before they go into the scrap bin. The information is only available once, and it is the basis for every decision below.

  1. Record the part number, the plow it came off, and the deployment hours or lane-km it covered.
  2. Measure remaining edge height at three points: both ends and the centre. Wear is rarely even, and the pattern tells you about down-pressure and operator technique.
  3. Photograph the wear face and the hole area. Elongated or cracked holes indicate a mounting or torque problem, not a steel problem.
  4. Note the wear pattern type: even, centre-heavy, one-end, or chamfered. Each points to a different corrective action.
  5. Check the moldboard or base edge the cutting edge sat against. A worn base edge will destroy a new cutting edge quickly.
  6. Separate the set into three piles: refit, hold as spare, retire. Do not skip the middle pile; a partially worn set is useful as an emergency spare.
  7. Log everything against the plow, not against the purchase order. Next year’s buyer will search by plow.

Reading wear against specification

Wear life depends on the steel grade, the edge section, the surface being cleared, and the down-pressure the operator runs. Published life figures for cutting edges are usually expressed as ranges for that reason, and any single number quoted without conditions should be treated with caution.

As a working rule, a carbide or hardened edge will typically outlast a standard carbon steel edge by a multiple rather than a percentage, but the multiple depends on abrasion severity. On smooth asphalt with light down-pressure, the gap narrows. On chip-seal, gravel shoulders, or lot clearing with heavy down-pressure, it widens considerably. Cost per hour of service, not cost per edge, is the number to compare.

Wear pattern observed Likely cause Close-out action
Even across full width Normal abrasion, correct mounting Refit if above minimum height; otherwise retire and re-order same specification
Centre-heavy Crowned surface, excessive down-pressure, or flexible moldboard Check base edge flatness and down-pressure setting before re-ordering
One end worn Plow running off-level, or operator bias Inspect linkage and shoe adjustment; consider rotating sets between plows
Chamfered or rounded leading face High-speed contact with hard aggregate Review grade selection; standard steel may be adequate if wear is this mild
Cracked or elongated holes Loose mounting, incorrect torque, or mismatched hole spacing Verify hardware and torque sequence; confirm dimensions against the product page

Dimensions and hole spacing follow the product page specification. Do not assume a replacement set will match a previous supplier’s pattern without checking.

What close-out means commercially

Cutting edges are a low-value, high-consequence part: cheap relative to a plow, expensive relative to a missed storm. That shapes the commercial decision more than price per unit does.

Ordering at close-out generally gives you the widest choice of section and grade and the most room on lead time. Ordering in late autumn compresses the same decision into a window where production schedules are full and freight is tighter. Lead time for standard sections is typically measured in weeks and depends on quantity, section, and whether the profile is a stock item; non-standard hole patterns add time. Minimum order quantities vary by section and by whether the edge is cut from stock plate or produced to order, so a mixed pallet across several plow types is usually more efficient than several small orders.

On total cost, the calculation that survives scrutiny is cost per service hour including change-out labour and downtime. A cheaper edge that is changed twice as often is rarely cheaper. At the same time, specifying a premium grade on a plow that sees light duty is a cost with no return. Segment your fleet by duty level first, then specify.

Specification risk is the quiet one. A part number that has drifted from the original drawing, a hole pattern that was “close enough” last year, or a section change made without telling the maintenance team will all surface in the first storm. If your procurement runs through public tenders, the tabulation stage is where these mismatches are caught or missed; see reading public bid tabulations for cutting edges for how to read those documents properly.

Building the re-order list

Once inspection is done, convert the three piles into a purchase plan with quantities and timing attached.

Start from the refit pile and the hold pile, then add a buffer based on how many sets you consumed last season and how severe the coming season is forecast to be. For most fleets, holding one spare set per high-duty plow and a shared pool for light-duty units is a reasonable starting structure; the right number depends on your storm frequency and workshop turnaround time. Confirm the section, grade, and hole pattern against the product page for each line before the order is raised, and consolidate lines where MOQ makes it sensible. If you are comparing suppliers, ask for the same section and grade across quotes, otherwise the comparison is not like for like. Full specification detail for each edge type is on the SENTHAI cutting edges range.

Handover to next season

Close-out is only complete when the next person can act on it without asking you questions. Write the per-plow record, file the photographs, and note any specification change with the reason. Flag the plows where the base edge or linkage needs attention, because those will otherwise be fitted with new cutting edges and wear them out prematurely. Set a reminder for the pre-season fit so the re-order arrives with time to spare rather than in the week before the first forecast snow.

Quick summary

Season close-out is an inspection and planning exercise: measure the edges off the plow, classify wear by pattern, and convert that into a re-order list segmented by duty level. Order early enough to get the section and grade you want, and compare suppliers on cost per service hour rather than unit price. Confirm every hole pattern and dimension against the specification before the order is raised.

Sources checked on 2026-11-16: SENTHAI Tools product specification pages for cutting edge sections, grades and hole patterns; internal note on public bid tabulation reading for cutting edges.

Three more perspectives

Workshop. The workshop cares about fit and change-out time. A set that matches the existing hole pattern and hardware goes on in one shift; a set that is “close” costs a re-drill and a lost truck. Give the workshop the measured record from last season, not just a part number.
Purchasing. Purchasing cares about lead time, MOQ and like-for-like comparison. Ask for section, grade and hole pattern on every quote, and consolidate lines so MOQ works in your favour rather than against it.
Field. The operator sees the wear pattern first. A short note from the operator on down-pressure, surface type and any unusual contact is worth more than a photograph taken weeks later.

Limits

This page is a planning framework, not a specification. It does not state wear life, cost, or lead time for any specific product, and it does not replace the dimensional data on the product page or the requirements of your own procurement process. Figures quoted by any supplier should be checked against your own fleet records before they are used in a budget.

Products discussed in this thread

Send us a blade drawing and get a quote back

Tell us the machine, the material you are clearing and the wear life you need. Our engineers reply with the edge profile, carbide grade and packing that fit the job — usually within one working day.