Skip to content
Carbide snow plow blades, inserts and wear parts — engineered in Rayong, Thailand
Request a Quote

How to size a bolt-on edge for a pickup plow

A bolt-on edge is sized by matching three dimensions to the plow blade: the bolt hole pattern (spacing and count), the edge height and length, and the edge…

A bolt-on edge is sized by matching three dimensions to the plow blade: the bolt hole pattern (spacing and count), the edge height and length, and the edge thickness the blade was designed to carry. Measure the existing edge or the blade’s bolt pattern first, then confirm hole diameter and countersink type. Length should match the moldboard width, not the vehicle.

Start from the blade, not the truck

Pickup plows are sold by vehicle class, but the cutting edge interfaces with the moldboard, and moldboard dimensions vary by manufacturer and model year. Two trucks of the same class can carry plows with different bolt patterns and edge heights.

The reliable starting point is the plow itself. Record the following before opening any catalog:

  1. Bolt hole spacing, center-to-center, measured across at least three holes to catch cumulative error.
  2. Total hole count and pattern symmetry — some blades use an offset or staggered row.
  3. Hole diameter and whether the blade uses countersunk, carriage, or plain hex bolts.
  4. Edge height from the top bolt row to the bottom wear face.
  5. Edge length, measured along the moldboard’s full width.
  6. Current edge thickness, measured with a caliper at an unworn section.

A common error is ordering by plow brand alone. Within one brand, light-duty and heavy-duty moldboards often take different edge thicknesses and bolt sizes. Model differences are covered on the product page.

Match the bolt pattern before anything else

The bolt pattern is the hard constraint. If hole spacing or count is wrong, no amount of correct height or thickness will make the edge fit, and re-drilling hardened steel is not a field option.

Measure spacing between hole centers, not edge-to-edge. On a worn edge, bolt holes may be elongated; measure at the unworn upper portion of the hole where possible. Confirm bolt diameter separately — a 1/2 in and 5/8 in pattern can look similar at a glance but will not interchange.

Parameter How to measure Typical range (pickup class) Risk if mismatched
Hole spacing Center-to-center, three holes minimum Varies by moldboard; commonly 6–12 in Edge will not bolt on
Hole count Count full pattern, note symmetry Typically 5–10 per edge Partial fit, stress concentration
Hole diameter Caliper or drill gauge Depends on bolt grade and plow class Bolt play, loosening, hole wear
Edge height Top bolt row to bottom face Commonly 4–8 in Interference or insufficient wear stock
Thickness Caliper at unworn section Depends on duty class; roughly 3/8–3/4 in Blade and hardware overload or premature wear
Length Full moldboard width Matches plow width, typically 6–9 ft class Overhang or uncovered moldboard ends

Height and thickness: what the blade was built to carry

Height and thickness are a system, not independent choices. The moldboard, trip mechanism, and lift hardware are designed around a specific edge mass and wear volume.

Going thicker than the original specification adds weight at the lowest point of the plow and increases load on trip springs and lift components. Going thinner reduces wear life and can deflect under load, which accelerates bolt loosening. Height affects how much wearable material sits below the bolt row; too much height on a light moldboard can reduce ground clearance at full lift. Where the application allows reversing the edge, the rules differ — see whether a cutting edge can be flipped.

Wear life depends on surface type, down-pressure, operator technique, and abrasives in the substrate. Gravel and unpaved lots can consume an edge several times faster than smooth asphalt. Quoting a single service life figure across applications is not meaningful; give buyers a range and state the assumptions.

Material and hardness selection

Hardness is a trade-off between wear resistance and impact toughness, and the right point depends on the surface being plowed and the operator’s speed.

Standard carbon steel edges suit mixed or unknown surfaces and are forgiving under impact. Boron or heat-treated grades raise wear resistance for high-abrasion, high-hour fleets, but become more sensitive to cracking on rough substrates or at high plow speeds. For a fleet running both paved lots and gravel yards, a mid-range hardness often produces lower total cost than a maximum-hardness edge that fails by cracking. Specification detail by grade is listed on the bolt-on edge product page.

The commercial side: MOQ, lead time, and specification risk

For distributors and fleet buyers, the sizing decision is also a stocking decision. A correct fit reduces returns and warranty claims; a near-fit generates the most expensive kind of claim because the part looks right and fails in service.

Practical points to settle before ordering:

  • MOQ: Non-standard hole patterns usually carry higher minimums than catalog patterns, because they require dedicated drilling or punching setups.
  • Lead time: Stock patterns ship from inventory; custom patterns depend on setup scheduling and raw material availability. Ask for the lead time on the specific pattern, not a general figure.
  • Total cost: Compare cost per plow-hour rather than unit price. A cheaper edge that wears faster or cracks early usually costs more once labor and downtime are counted.
  • Specification risk: Confirm the pattern in writing with hole spacing, diameter, count, height, and thickness. A photo of the old edge next to a ruler is a low-cost way to prevent a wrong shipment.
  • Consistency: For fleet procurement, batch-to-batch consistency in hole pattern and hardness matters more than any single-edge advantage.

Verification before the order is released

A short check before release catches most sizing errors. Run it against the physical plow or a documented drawing, not a memory of the last order.

  1. Confirm hole spacing across three or more holes.
  2. Confirm hole count and pattern symmetry.
  3. Confirm bolt diameter and head type.
  4. Confirm edge height and length against the moldboard.
  5. Confirm thickness against the original specification or blade rating.
  6. Confirm material grade against the surface and duty cycle.
  7. Record all values on the purchase order.

Quick summary

Size a bolt-on pickup plow edge by the blade’s bolt pattern first, then height, length, and thickness as a matched set. Material and hardness follow from the surface and duty cycle, and wear life should always be quoted as a range with stated assumptions. Confirm every dimension in writing before releasing the order.

Sources checked on 2026-11-16: SENTHAI Tools product documentation for bolt-on cutting edges; published plow manufacturer fitment guidance; general mechanical fastening practice for hardened steel wear parts. Ranges reflect common pickup-class configurations and vary by moldboard design.

Three more perspectives

Workshop

In the shop, the edge that fits is the one that comes off and goes back on with the same bolts in the same holes. Techs care about hole alignment and whether the bolts are reusable. An edge that needs persuasion with a drift pin slows the changeover and often ends up with loose hardware a week later.

Purchasing

Purchasing sees the pattern as a part number and the risk as a return. The useful data points are the confirmed hole pattern, the MOQ for that pattern, and the lead time quoted for it specifically. Cost per unit is secondary to cost per season across the fleet.

Field

Operators judge an edge by how it wears and whether it stays tight. A slightly thicker edge that fits the blade correctly usually outperforms a harder edge that was never designed for that moldboard, particularly on mixed surfaces where impact loading is routine.

Limits

This article covers sizing logic for bolt-on pickup plow edges only. It does not provide fitment data for specific plow models, torque specifications, or warranty terms, and it does not address poly or rubber edges, trip mechanism repair, or hydraulic system sizing. Model differences are covered on the product page.

Products discussed in this thread

Send us a blade drawing and get a quote back

Tell us the machine, the material you are clearing and the wear life you need. Our engineers reply with the edge profile, carbide grade and packing that fit the job — usually within one working day.