Skip to content
Carbide snow plow blades, inserts and wear parts — engineered in Rayong, Thailand
Request a Quote

El Nino Winters and Southern Fleets: Planning Edges for Occasional Snow

For: a southern or mid-Atlantic public works or contractor fleet that plows a handful of times a year.

Illustration for el nino winter snow: a regional map with a pin, a snowflake and a carbide cutting-edge cross-section
4 answersAsked 24 October 2026·Seasons & Calendar

SENTHAI Editorial Team

TALK / SEASONAL PLANNING DISCUSSION
Buyer question

We run trucks in a southern region where snow is occasional. With an El Nino winter forecast, how many edges and spares should we really keep on hand?

For: a southern or mid-Atlantic public works or contractor fleet that plows a handful of times a year. Short answer: do not buy more edges on the strength of a wet outlook. Make sure the edges you already have are ready, because occasional-snow fleets lose more edges to storage and neglect than to wear.

What NOAA’s October 2026 discussion says for your region

The outlook is a probability, and it should change the plan rather than the order.

  • CPC favors above-normal precipitation for much of the Southeast, the Central and Southern Plains and the eastern seaboard, with the greatest likelihood of wetter-than-normal conditions in the Southeast and Florida.
  • For temperature, near-normal is favored for much of the Southeast, and above-normal for the Ohio Valley and mid-Atlantic.
  • The outlook is for seasonal averages. A wet, mild winter is not the same as a snowy one, and CPC does not forecast individual storms.

What this suggests, and what it does not

Wetter odds in a warm region mostly mean more rain. They may also mean a higher chance that one cold event arrives with moisture already in place. That is a reason to be ready, not a prediction. Plan for one or two events, not a season total.

A readiness plan for occasional-snow fleets

When Do this Why
Now (October) Pull each plow out of storage and check the edge for rust-bound bolts, cracks and remaining height A rarely used edge fails on mounting hardware and corrosion before it wears out
Before first forecast cold snap Test lift, angle and float on every truck; bolt up a spare edge on the truck most likely to run You will have hours, not days, of notice
Event day Assign who changes an edge, where the spare and tools are, and who calls the supplier Crews with little snow experience lose time on unfamiliar tasks
After the event Wash, dry, inspect and note edge height before returning to storage Salt residue left on steel through a mild spell speeds rust

One planning trick: write a one-page event card for the plow program, listing who is on call, which routes come first and where spare edges are kept. A fleet that plows twice a year will not remember these details from the last storm, so the card is the memory.

Boundary: the table is operating advice, not a result from NOAA. Your climatology, local snow history and mutual-aid agreements matter more than an outlook map.

↳ Replying to SENTHAI Editorial Team

Occasional-snow fleets should buy for readiness: one spare edge and a bolt set per active truck is a common starting point, though the number is your call. Spend before the season rather than during an event, when suppliers’ stock and freight options are tightest and prices are less negotiable. Ask the supplier whether unused spares can be returned or rolled into next season’s order.

↳ Replying to Purchasing perspective

If plowing happens only a few times a year, resistance to corrosion on idle steel and ease of change-out may matter more than maximum wear life. Weigh that honestly against the cost of a premium edge that mostly sits in a shed. Ask suppliers about storage coating, not just wear claims. A coated edge that survives two summers in a shed may be worth more to you than a longer-wearing one that rusts at the mounting face.

↳ Replying to Selection perspective

Idle plows seize. Grease pivots, cycle the hydraulics during the preseason check and confirm the electrical connections work before the forecast turns. A forty-minute test on a dry day avoids a failed lift on an icy road with a crew that is already stretched. Replace any hose or fitting that shows weeping or cracking while the truck is still in the yard.

Next step

For: a southern or mid-Atlantic public works or contractor fleet that plows a handful of times a year.

Send us a blade drawing and get a quote back

Tell us the machine, the material you are clearing and the wear life you need. Our engineers reply with the edge profile, carbide grade and packing that fit the job — usually within one working day.