Skip to content
Carbide snow plow blades, inserts and wear parts — engineered in Rayong, Thailand
Request a Quote

Cost per push on dirt road: what to measure

Cost per push on a dirt road is the total cost of a cutting edge divided by the number of grading or plowing passes it survives, expressed per…

Cost per push on a dirt road is the total cost of a cutting edge divided by the number of grading or plowing passes it survives, expressed per pass rather than per edge. You measure it with three inputs: edge purchase price, change labour and downtime, and the number of passes until the wear surface is no longer usable. On unsealed roads, that number is usually driven by abrasive wear and hole/bolt condition, not by impact.

Why per-push costing beats price per edge

On a dirt road the edge is consumed by abrasion, so a cheaper edge that lasts proportionally less is not cheaper. Per-push costing forces the buyer to compare like with like across suppliers and across edge specifications.

It also exposes the cost that never appears on a quotation: the grader parked while a fitter swaps blades, and the crew waiting. On a short season, downtime can outweigh the steel cost.

The measurement inputs you actually need

You do not need a laboratory. You need three records kept consistently for a defined period, ideally one full season on a known road section.

  1. Edge cost per change — purchase price per edge, plus freight and duty landed, divided by the number of edges fitted per mouldboard.
  2. Labour and downtime per change — machine hours stopped, fitter hours, and any mobilisation cost to bring the crew and tooling to the machine.
  3. Passes between changes — count from the machine’s own records or the operator’s log, on the same road class and material.
  4. Wear-out criterion — define it in advance: remaining usable depth, loss of the bolt-head seat, or a set number of holes elongated. Mixed criteria produce meaningless comparisons.
  5. Road and material notes — gravel, crushed rock, sand, or mixed with fines; these change wear rates substantially.

How to calculate cost per push

The arithmetic is simple; the discipline is in keeping the inputs comparable. Use landed cost, not list price, and include the change event.

Input What to record Typical range (depends on)
Landed edge cost Price + freight + duty per edge set Depends on size, steel grade, hole pattern, order volume
Change labour Fitter hours × rate, plus supervisor Depends on bolt count, corrosion, access
Downtime Machine hours stopped × hourly machine cost Depends on fleet utilisation and season
Passes per edge Logged passes to wear-out criterion Depends on abrasive content, moisture, down-pressure
Cost per push (Edge + labour + downtime) ÷ passes Usually a range across a season, not a single value

Report cost per push as a band, for example a low and high figure from different road sections, rather than one number. Single figures invite false precision and get argued over instead of used.

Wear patterns that distort the number

If one end of the edge wears faster, your passes-per-edge figure is being set by the worst point, not the average. That is a specification and fitment question before it is a purchasing question.

Common causes are a mouldboard that is not true, uneven bolt torque, mixed bolt grades, or an edge that does not match the original hole layout. See the checks in one end of the edge wearing faster before you attribute short life to steel quality.

Also separate front-edge wear from end-bit wear. They are different parts with different duty and should be costed separately.

What this means commercially

Per-push costing changes what you specify and what you stock. A higher-grade edge with a longer life can reduce total cost even at a higher unit price, but only if the wear mode is abrasion and the fitment is correct.

Practical procurement points:

  • MOQ and mix: consolidating sizes into fewer orders lowers landed cost per edge, but ties up capital. Balance against the number of machines and the season length.
  • Lead time: a long lead time forces larger safety stock, which raises holding cost and can push you toward a cheaper edge you can get quickly. Price that trade-off explicitly.
  • Specification risk: an edge that does not match the mouldboard hole layout causes rework, elongated holes, and premature loss. That risk belongs in the per-push calculation, not outside it.
  • Consistency: batch-to-batch variation in hardness or hole position makes your pass counts noisy. Ask suppliers for dimensional and hardness tolerances, not just grade names.

Check the drawing and hole layout on the product page before ordering.

Setting up a simple trial

Run the comparison on two or three machines on comparable road sections for a defined period. Keep the change crew and torque procedure constant, otherwise you are measuring the workshop, not the edge.

Record passes, change time, and the wear-out criterion for each edge set. Review at the end of the period and convert to cost per push. For product specifications and hole options, start from the cutting edge product page and confirm dimensions against your mouldboard drawing.

Quick summary

Cost per push is landed edge cost plus change labour and downtime, divided by passes to a defined wear-out criterion, reported as a range. On dirt roads the dominant variables are abrasive wear, fitment accuracy, and how fast you can change an edge. Keep the inputs consistent or the comparison is worthless.

Sources checked on 2026-11-18: SENTHAI Tools product and technical pages (cutting edge specifications, hole layouts); internal wear and fitment notes referenced on the linked talk page. No independent field study was used; figures are given as ranges and depend on site conditions.

Three more perspectives

Workshop

Change time is the variable the workshop controls. Seized bolts, worn bolt heads, and mismatched hole patterns turn a short job into a long one. Keep a torque procedure and inspect bolt seats at every change; that alone stabilises the labour half of the per-push figure.

Purchasing

Compare landed cost per edge against expected passes, not unit price against unit price. Ask for tolerances and lead time in writing, and treat a long lead time as a cost item because it drives safety stock. Volume discounts only help if the sizes match what the fleet actually fits.

Field

Operators see the wear first. A short daily note on road material, moisture, and any abnormal wear pattern gives you the context that makes pass counts comparable across machines and seasons. Without it, the numbers drift and the comparison collapses.

Limits

This page is a measurement framework, not a warranty, a life prediction, or a quotation. It does not specify steel grades, torque values, or replacement intervals for any particular machine, and it does not replace the OEM drawing or the supplier’s fitting instructions. Actual wear rates and costs depend on site conditions, operator practice, and maintenance quality.

Products discussed in this thread

Send us a blade drawing and get a quote back

Tell us the machine, the material you are clearing and the wear life you need. Our engineers reply with the edge profile, carbide grade and packing that fit the job — usually within one working day.