Ask for the test method, the abrasive medium, the loss measurement basis, and the pass/fail criterion before you compare any two abrasion numbers. An abrasion figure without those four elements is a sales claim, not a specification. The questions below are the ones that separate a supplier who can support your wear programme from one who is quoting a number they cannot reproduce.
1. What exactly is being abraded, and how is loss measured?
Wear resistance is a property of the edge material and its heat treatment, not of the part number. Before discussing results, establish what the supplier actually put in the test.
- Is the specimen a finished cutting edge, a coupon cut from the same coil, or a separately sourced test piece?
- Is loss reported as mass loss (grams), volume loss (mm³), or dimensional wear (mm of edge recession)? These are not interchangeable across different material densities.
- How many specimens per condition, and what was the spread between them? A single result tells you very little.
- Was the worn surface examined, or only weighed? Grooving and plastic deformation behave differently from uniform abrasion.
If the supplier cannot describe the specimen provenance, treat the number as indicative only.
2. Which standard, and was it followed or adapted?
Most credible abrasion data traces back to a recognised method. The useful question is not whether a standard exists, but how closely the supplier’s procedure matches it and where it deviates.
| Question | Why it matters to you |
|---|---|
| Which standard is cited (e.g. ASTM G65, G105, G81, or an internal method)? | Determines whether results are comparable to your existing supplier’s data |
| Was the abrasive medium specified — silica sand, alumina, grit size, moisture condition? | Abrasive type changes ranking between materials; dry vs. wet shifts results substantially |
| Wheel speed, load, and number of revolutions? | Low-stress and high-stress regimes favour different hardness ranges |
| Was the procedure accredited, or in-house? | In-house is acceptable if the method is documented and repeatable |
| Is a reference material run alongside each batch? | Without a control, drift in the rig goes undetected |
A supplier who cites a standard but cannot state the abrasive specification is quoting a family of tests, not a result.
3. How does the lab number relate to field life?
Laboratory abrasion ranks materials under controlled conditions. It does not predict service life, because real ploughing adds impact, corrosion, and varying substrate. Expect a range, not a figure.
- Ask what field or fleet data, if any, correlates with the lab ranking. Typical correlation is directional, not proportional.
- Ask how the material behaves under impact alongside abrasion — a hard edge that chips can lose life faster than a softer one that wears evenly.
- Ask about hardness range and tolerance, not a nominal value. A spread of several HRC points across a batch changes wear outcomes.
Treat any single life figure with suspicion. Life depends on road surface, grit, down-pressure, and operator behaviour.
4. What does the test tell you commercially?
Abrasion data is a procurement input, not a headline. Its commercial value is in reducing specification risk and narrowing the number of grades you need to stock.
- Specification risk: if the supplier’s test method is undocumented, you cannot defend the grade choice internally when a fleet reports short life. Documented methods transfer with the purchase order.
- Supply and MOQ: a supplier running controlled abrasion tests usually casts or rolls in defined heats. Ask what MOQ applies per grade and whether test coupons are drawn per heat or per shipment.
- Lead time: grades with tighter hardness windows and post-wear testing typically carry longer lead times than commodity edges. Confirm whether the quoted lead time includes test release.
- Total cost: compare cost per operating hour across a range, not cost per kilogram. A higher-grade edge at a higher unit price can still reduce cost per hour if wear life improves enough — but only if the abrasion ranking is credible.
Where the data is weak, the practical response is to buy a trial quantity and measure edge recession yourself rather than accept a comparative claim.
5. Can the supplier reproduce the result on request?
Repeatability is the real test of a test. Ask whether the same procedure can be re-run on a sample you supply, and whether they will share the raw readings rather than a summary.
- Request the test report, not the datasheet line.
- Ask for specimen count and scatter.
- Ask whether the rig is calibrated and how often.
- Ask for a reference material result from the same session.
- Ask what changed in the last revision of the test method.
- Ask whether third-party verification is available.
Suppliers who can answer all six are usually the ones whose numbers survive a second purchase order. For background on how edge geometry affects wear patterns, see our note on one end of the edge wearing faster.
6. What should you check before ordering?
Test data describes material behaviour; it does not confirm the part fits. Verify the physical specification separately from the wear claim.
Check the drawing and hole layout on the product page before ordering, and confirm that the grade quoted in the test report is the grade listed for that part number. Where a supplier offers several hardness options, ask which one the abrasion data refers to — results are frequently published for the top grade and quoted against a standard SKU. Review the full cutting edge range to see how grades map to part numbers.
Quick summary
Abrasion numbers are only comparable when the method, abrasive, measurement basis, and acceptance criterion are all stated. Ask for the raw report, the scatter, and a reference material result; treat single life figures as indicative. Where documentation is thin, trial quantities and your own edge-recession measurements are the more reliable procurement route.
Sources checked on 2026-11-15: ASTM G65, G105 and G81 standard scopes; supplier test-report conventions; SENTHAI product and technical pages.
Three more perspectives
Limits
This page explains what to ask; it does not provide test results, grade recommendations, or life predictions for any specific material or site. Abrasion behaviour depends on substrate, machine, and operating conditions, and no laboratory method reproduces all of them. Verify current specifications and drawings with the supplier before committing to an order.
JOMA Style Blade — Rubber-Flex Edge with Carbide Wear Segments
Carbide Snow Plow Blade for Highway and Municipal Fleets
Tungsten Carbide Inserts for Snow Plow Edges